Kako namestiti ojačevalnik v Jeep JK?
Vsak lastnik avtomobila si želi imeti dober ozvočenje z vgrajenim ojačevalcem, ki se ne razlikuje od voznikov Jeep Wrangler JK.
Toda kako namestiti ojačevalnik v Jeep Wrangler JK? Ugotovimo.
Namestitev ojačevalnika v vaš Jeep Wrangler JK zahteva, da ustvarite nekaj dobrega prostora za namestitev ojačevalnika in mnogi ga raje namestijo pod prednji sedež. Potem, ko zagotovite prostor za ojačevalnik, poiščite boljši način za poravnavo žic na različne lokacije zvočnikov po avtomobilu. Končno napajajte ojačevalnik s stabilno in dosledno močjo in se prepričajte, da je ožičenje izvedeno pravilno.
V tem članku vam bom pokazal, kako ravnati z ojačevalnikom v Jeepu JK in kako ga pravilno namestiti.
Kako namestiti ojačevalnik v Jeep JK s poprodajnim radiem?
Pred namestitvijo ojačevalnika na poprodajni radio se prepričajte, da ste upoštevali vse potrebne in previdnostne ukrepe. Najboljše mesto za namestitev ojačevalnika je v prtljažniku, še posebej pri namestitvi velikega modela.
- Ojačevalnik pritrdite z vijaki v predhodno izvrtane luknje.
- Priključite napajalne kable na akumulator v kabini vašega Jeepa in jih razširite do mesta, kjer je nameščen ojačevalnik.
- Nato priključite ozemljitveno žico na ojačevalnik in neposredno na šasijo avtomobila.
Pri nameščanju ozemljitvene žice se prepričajte, da pride v stik s kovino, saj lahko vpliva na splošno delovanje ojačevalnika.
- Prepoznajte žice, ki te zvočnike povezujejo z radiem za poprodajne storitve, in jih obrišite, da odprete negativne in pozitivne žice.
- Priključite žico zvočnika na črtasta mesta in ju zategnite skupaj z električnim trakom.
- Priključite žice na ojačevalnik in poskrbite, da bodo vse žice pravilno nameščene. Prepričajte se, da na prave kanale povezujete prave zvočnike.
- Znova povežite priključke avtomobilskega akumulatorja, da preverite, ali je celotna povezava ojačevalnika na mestu.
Ko vklopite in se nič ne zgodi, ponovno priključite napajalni kabel na akumulator avtomobila in preverite ožičenje. Na tej točki je ojačevalnik v odličnem položaju za usklajevanje s poprodajnim radiem.
Namestitev ojačevalnika
Namestitev ojačevalnika v Jeep Wrangler JK ni tako enostavna, kot se morda sliši. Morate biti zadovoljni in imeti osnovne informacije o tem, kako ojačevalnik deluje in kako deluje skupaj z avtoradio.
Upoštevajte, da je ojačevalnik pomemben del opreme, ki pomembno prispeva h visokokakovostnemu zvoku, ki ga proizvajajo zvočniki.
Ustvariti morate precej prostora za namestitev ojačevalnika in povezavo žic. Večina ojačevalcev je nameščenih bodisi pod sedežem ali v prtljažniku, kjer si lahko zagotovite nekaj dobrega prostora, ki je varen za njihovo namestitev in tudi za druge komponente.
Veliko ljudi se odloči za namestitev ojačevalnika pod sovoznikov sedež, da se izogne nevšečnostim. Poleg tega je namestitev ojačevalnika pod prednji sedež lahka naloga, ki ne vključuje veliko zapletov, razen napeljave žic skozi kabino.
Poleg tega, če postavite ojačevalnik na tla Jeepa Wranglerja, ga izpostavite možnemu tveganju, da ga prizadene vlaga ali prah.
Katera orodja potrebujete za namestitev ojačevalnika v Wrangler JK?
Številni ojačevalniki so opremljeni s celotnim ožičenjem , kar zmanjša dodatno iskanje žic ali konektorjev, vendar raje dobim ločene žice v natančni velikosti, ki jo potrebujem za določen sistem.
Odlične žice, ki jih uporabljam, so iz Knukonceptza , tako da če želite dobiti nekaj najboljše kakovosti, jih preverite na Amazonu.
Druga stvar, ki jo morate imeti pri namestitvi ojačevalnika, je vgrajena varovalka . Prepričajte se, da uporabljate vrsto varovalke, ki jo priporoča proizvajalec ojačevalnika.
Potrebovali boste tudi ozemljitveno žico, žice za daljinski vklop, RCA kable, konektorje in sam ojačevalnik. Ne pozabite, da se morajo priključki popolnoma ujemati s priključnimi sponkami in velikostjo žice.
Poleg tega bo velikost ojačevalnika, ki ga kupite, samodejno določila količino prostora, ki ga potrebujete, in če imate omejen prostor v avtu, razmislite o namestitvi pod, za ali med sedeže.
Ne pozabite tudi, da ojačevalniki proizvajajo toploto in potrebujejo neko obliko hlajenja. To pomeni, da mora položaj, kamor postavite ojačevalnik, omogočati prosto gibanje zraka.
Če nameščate globokotonec, je odlična ideja, da ojačevalnik namestite neposredno v ohišje.
Razmislite, kako boste izvedli napeljavo kablov od ojačevalnika do glavne enote stereo naprave in napajanje iz avtomobilskega akumulatorja. Dobro je napeljati napeljavo pod talnimi oblogami čez spodnje pragove vrat.
Kabli RCA morajo biti tesno nameščeni na nasprotnem delu avtomobila od napajalnih žic, da preprečite kakršno koli motnjo. Poiščite položaj varovalke vašega ojačevalnika pod pokrovom in poiščite najkrajšo možno pot do nje.
The power cable should pass through the firewall for safety purposes. Try using the existing holes available to avoid drilling new holes across the firewall.
How to Fit the Amplifier in the Jeep Wrangler JK?
Before beginning the fitting process, ensure you have enough wiring to clear the job.
If the wiring is not enough, locate the best position to place the amplifier that will work perfectly with the wiring you have at hand.
Disconnect the positive terminal of the battery before beginning any work. Besides, ensure that you clearly understand what is behind the spot where you want to drill a hole. This will help you to avoid damaging any components.
To make a perfect hole, start by making a small pilot hole, then drill out the ideal hole size you need to use.
Next, fit a rubber grommet in the hole to prevent the sharp steel edge from damaging the wire.
Position the amplifier perfectly and mark the mounting holes with a pencil or any form of marker. Then, go ahead and drill the holes where the amplifier is located.
Run all the wiring in the perfect positions and cut them depending on the required length. Do not make wires too short. It is better to have a one foot extra than missing 2″.
How to Wire the Amplifier in a Jeep Wrangler JK?
Eliminate the insulation from all ends of the wires to give room to attach the connectors.
Note that some amplifiers require a connection using only bare wires, especially for the power wires.
Connect the ground wire to a metal point connected to the Jeep’s chassis or the best grounding point available. The ground wire should be placed directly to the bare chassis metal, not the painted surface, so you have to clean any form of paint to ensure excellent ground connection.
Connect the RCA leads, speaker leads, and the remote turn-on system from the amplifier directly to the back of the head unit. However, some head units do not have the remote turn-on wire option. In this case, wire the remote turn-on of the amp to the power wire connecting the head unit or another wire running the accessory switch, or you may need to add an on/off switch on the amplifier power wire.
This is mainly meant to help avoid the amplifier remaining on once you have switched off your ignition, and it prevents the amplifier from draining off your car battery without your consent.
Connect the rear, front, and the wires of the subwoofer speaker from the amplifier to the other corresponding speakers.
Connect the inline fuse to the primary power cable holding all the connections to the end of the leads.
The fuse holder needs to be installed on a solid structure inside the engine space, ideally no longer than 18″ from the battery’s positive terminal.
Connect the amp power cable to the battery’s positive lead and reconnect the positive battery lead to the positive terminal.
After the power supply is on, secure all the wiring using the cable ties. At this point, you need to test all the amplifier operations using the fade, balance, and subwoofer settings on the head unit.
Ensure that every speaker is working independently without any static or distortion.
Benefits of Using One Amplifier for Speakers and Subwoofer
Installing an efficient amplifier in your Jeep Wrangler JK comes with a bunch of benefits.
- Using one amplifier for all speakers save the battery from draining, increasing its lifespan.
- In addition, integrating one amplifier to the subwoofer and speakers is easier than setting up two amplifiers. This saves your time and the space to set up the amplifier. Remember, the amp needs some considerable space to accommodate the wiring.
A single amplifier is easy to balance and increases adaptability. This works better, especially if you have at least a five-channel amplifier.
Go for an advanced model with incredible power whenever you think about installing one amplifier to operate the speakers and the subwoofer.
Best Amplifiers for Jeep Wrangler JK
Boss Audio Riot
This is a classy mono-block from the Boss Audios Riot series which is is ideal for supplying power tot your subwoofer. The primary factor that makes it stand out is its low price and high quality. It’s made in the A/B class, with incredible abilities to generate exceptional output.
The amplifier can withstand high amounts of power output. It rocks with an impressive 1100 watts at only 2 ohms giving you a general RMS of about 825 watts. It comes with both high and low-level inputs that help it achieve an optimal performance.
This amplifier has a variable low pass filter that gives you total control of what penetrates through the car subwoofers.
The woofer levels can be easily controlled using a remote controller to boost the bass function. Its design can perfectly fit in the trunk or between the seats.
Rockford R300X4 Prime
Rockford is a fantastic four-channel amplifier choice that is also an excellent choice for Jeep Wrangler JK.
It is made in the A/B class, and it is equipped with a heat sink that ensures everything is running smoothly and does not overheat.
It is a versatile amplifier that can run the entire system smoothly without any complications. The amp can run all the components, including the front channels and the subwoofer at the bridge mode.
Rockville dB45
The Rockville car amplifier is a powerful audio system that perfectly fits a Jeep Wrangler JK. It generates a power output of 3200 watts to run all the speakers and the subwoofer in the car.
It has a four-channel output generating high output and a low impedance solution that can power the car’s bass speakers.
Besides, this amplifier features an incredible subsonic filter with a fully adjustable crossover.
The amp has a bunch of circuitry that enables users to adjust the bass settings depending on their preferred bass taste. It features an inbuilt soft start technology that prevents the amplifier system from starting on a high volume.
Zaključek
Installing an amplifier in a Jeep Wrangler JK from scratch is not the easiest task, but with the above-detailed guidance, you can easily acquire a new amplifier and install it in your car without any problem.
However, you need to ensure that you abide by all the precautions for your safety and your Jeep Wrangler JK. However, you need to ensure that you comply with the safeguards for your protection and your Jeep Wrangler JK.